Brick Outdoor Wood

Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax


Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax
Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax
Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax
Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax
Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax

Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax    Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax
Industrial Multi Surface Coatings by PaintMAX Top Quality Floor Paints and Coatings. Made for high impact, heavy traffic Industrial areas. Ideal for all work unit, Factory, Car show room, Home Garages and all concrete floors and walls. Formulated to last using Polyurethane This product will withstand the test of time. We have designed this product to work under the pressures of Heavy Vehicles, Jet Washing and Surface Water, Grease and Oil residue, Continuous Footfall, All Weather Conditions both on Interior and Exterior Surfaces. All Stock is new and unopened. This product is ready to use, single pack, No Mixing products required. Apply quickly and simply with Roller or Brush.

A 20 LITRE CAN WILL COVER AROUND 80 SQ METRES. This Multi surface PaintMAX Paint will cover interior or exterior concrete, wood, masonry and metal work.

Extremely durable, easy product to work with. This Listing is for 40 litre.

(areas covered : London, Kent, Essex, Hertfordshire, South East). PLEASE CONTACT BEFORE PURCHASING 0203 589 2280.

COLLECTION AVAILABLE FROM BROMLEY BR1 or HALSTEAD CO9. The information set out in this section should be used as a guide, results can vary depending on age, condition of surface and previous coatings that have been applied. Weather conditions and ventilation may also play a part in drying times. Mix very well before use using a drill/paddle tool. Where the floors have been subjected to oil and grease, We recommend steam cleaning your floors and use our Heavy Duty Surface Deep Clean before.

Application of any floor coating after allowing the surface to dry and PaintMax Pre Seal has been used. A floor coating does not do well if you have any moisture issues Hydrostatic pressure from the moisture can actually cause the coating to peel up, sometimes taking pieces of the concrete with it.

Should floors be devoid of an effective Damp Proof Membrane (DPM), virtually any paint will lift and peel off the surface. Indeed, even self-levelling screeds can be pushed up by water pressure. This is another nightmare regularly experienced by many companies. For this reason, a damp proof coating is recommended as a solution before applying a floor paint. Treating your floor/surface before coating them.

It is important to'treat' your surfaces before coating them to prevent issues post-paint. Before painting your floor or surface, it is important to repair any cracks, holes or expansions of joints in your concrete to prevent an un-slightly finish to your flooring once it's painted. PaintMax Pre Seal is designed to seal the surface from the out-gassing of the concrete, where air will rise and be expelled from the concrete which is often caused by a rise in temperature or a change in humidity.

Another major cause to poor flooring is rising damp. Due to a poor or non-existent DPM (Damp Proof Membrane), the damp is caused by a rising water table and/or the immediate surrounding areas being waterlogged. Air entrapment is a common issue that can occur if the surface isn't primed before being coated.

This is where the air pushes bubbles into the resin coat which later bursts, leaving'craters' and'pin holes' in your floor paint. This can also be caused when the resin has been mixed too quickly - it is important to use the correct tools to mix to avoid issues. Primer tackles this issue by soaking further into the surface to fully seal the entire surface area of concrete floors. Air is then less likely to push up, and on the rare occasion that it does, the bubble will pop and the resin now being thinner, will generally revert back and refill the'pin hole' caused by the bubble. Coverage:6/8m squared per litre. 60/80m squared per 20 litre can. Depending on surface age and conditions. Dry time of coating using standard roller in areas with minimal air moisture (lab conditions). First coat should be left to dry for 24 hours to assure adhesion to surface leave minimum of 24 hours for after coats always leaving minimum of 48 hours before 100% use of area again. True 100% cure will only be 7 days after application of last coating. (work in a well ventilated area using no forms of naked light/fire). Please test for damp before coating by applying a small test patch or applying a clear plastic sheet (30cmx30cm) and sealing it to the floor with a high grade tape (duck tape) with out any ways of air escaping and leave for 24 hours if there is any forms of water vapour on the sheet the are will have damp and steps will need to be taken before coatings. If the area you are looking to coat is virgin (never been coated) or has had contamination from oil, grease, cutting agents etc, Cleaning with correct equipment/surface preparation products will be required. Powerfloated/Screed areas (smooth shinny concrete) will need to be treated with a acid etch or abrade by mechanical means all product info will be displayed on the item you will take collection of.

A test patch is always advised as some areas my still have contamination and this could have complications when coating. Orders will be dispatched same day if ordered before 12:00. Or keep a note of batch code from lid of can. PRE-SEAL ITEM IS A UNDERCOAT/SURFACE SEAL AND SHOULD ALWAYS BE OVER COATED WITH A FLOOR PAINT PRODUCT THE PRE-SEAL PRODUCT ON ITS OWN WILL NOT ACT AS A STABLE FLOOR COATING.

Floor-paint Products are polyurethane heavy duty high impact formulation and care should be taken when applied full safety data sheet can be requested. All images are for illustration purposes only including main images shade difference may happen from image to product. Any recommendations and advice offered are given without legal responsibility. PaintMax shall not be liable to any person for any loss or damage which may arise from advice given or from the use of any of the information contained in any of the materials offered on this website. Ideal for interior or exterior use. High impact durable polyurethane paints for concrete floors, walls, wood and metal products. Collection from Bromley BR1 or Halstead CO9.

Same day and Next day. Please contact before purchasing to arrange, call : 0203 589 2280.

Postal orders will be dispatched same day if ordered before 12:00. This item is in the category "Home, Furniture & DIY\DIY Materials\Paint, Stain & Varnish\Interior & Exterior Paint". The seller is "paintmaxpro" and is located in this country: GB. This item can be shipped to United Kingdom.

  1. Colour: VARIOUS
  2. Country/Region of Manufacture: United Kingdom
  3. Application Method: brush, Paint, Roll
  4. Base Material: Polyurethane
  5. Container Size: 40 L
  6. Unit Quantity: 20 Litre
  7. Drying Time: 24 Hours
  8. Type: GARAGE FLOOR
  9. Features: For Interior, For Outdoor Use
  10. Finish: Semi-Gloss
  11. Room: Patio, work unit, Any Room, Basement, Garage, Guestroom, Hallway, Utility/Laundry Room
  12. Paint & Primer In One: Yes
  13. Packaging: Can
  14. Brand: PAINTMAX
  15. Suitable For: Aluminium, Barn & Fence, Brick, Concrete, Deck, Flooring, Furniture, Garage Door, Masonry, Metal, Porch & Floor, Wall, Wood


Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax    Floor Paint-factory-garage-showroom-large 40ltr Grey Paintmax