GARAGE FLOOR PAINT - CONCRETE FLOOR PAINT - FACTORY FLOOR PAINT - PAINTMAX PROFESSINAL PU350. Is our most durable long lasting Surface Paint.
PaintMaxPro Floor Paint will cover interior & exterior concrete Flooring. Made for high impact, heavy Industrial traffic Flooring areas. Ideal for surfaces where heavy Farm Machinery/HGV's operate, work units, Factory floors, Car Show rooms, Home Garages and all concrete floors and walls/surfaces that are open to the elements. Formulated to last using PU350 Polyurethane.
This product will withstand the test of time. We have designed this product to work under the pressures of Heavy Industrial Vehicles, Jet Washing and Surface Water, Grease and Oil residue, Continuous Footfall, All Weather Conditions both on Interior and Exterior Surfaces. This PaintMAX Floor Paint will cover interior & exterior concrete Flooring. Made for high impact, heavy traffic Industrial Floor areas. Ideal for all work units, Factory, Car Show room, Home Garages and all concrete floors and walls.
Formulated to last using PU150 Polyurethane. We have designed this product to work under the pressures of Industrial Vehicles, Jet Washing and Surface Water, Grease and Oil residue, Continuous Footfall, All Weather Conditions both on Interior and Exterior Surfaces. All Stock is new and unopened.This product is ready to use, single pack, No Mixing or Hardener products required. Apply quickly and simply with Roller, Brush or Spray. A 20 LITRE TUB WILL COVER BETWEEN 60 & 80 SQ METRES. This PaintMAX Polyurethane Oil based Paint is ideal for all interior & exterior concrete, wood, masonry and metal work Products. Extremely durable, easy product to work with. (Areas covered: London, Kent, Essex, Hertfordshire, South East) PLEASE CONTACT BEFORE PURCHASING. COLLECTION AVAILABLE FROM EPPING CM16 or BROMLEY BR1 or HALSTEAD CO9. Bulk orders, Trade and Pallet price (45x20L) available please contact for discount price. The information set out in this section below should be used as a guide, results can vary depending on age, condition of surface and previous coatings that have been applied.
Weather conditions and ventilation may also play a part in drying times. Mix very well before use, using a drill/paddle tool. We advise a test area (1 meter square) before applying product to complete surface.This is to test that product bonds to surface, the colour is correct and to check for contamination. Where the floors have been subjected to oil and grease, we recommend steam cleaning or jet washing your surface and use our Heavy-Duty Surface Deep Clean before application of any floor coating after allowing the surface to dry and PaintMax Pre Seal has been used. A floor coating does not do well if you have any moisture issues Hydrostatic pressure from the moisture can actually cause the coating to peel up, sometimes taking pieces of the concrete with it. Should floors be devoid of an effective Damp Proof Membrane (DPM), virtually any paint will lift and peel off the surface. Indeed, even self-levelling screeds can be pushed up by water pressure. This is another nightmare regularly experienced by many companies. For this reason, a damp proof coating is recommended as a solution before applying a floor paint. Treating your floor/surface before coating them. It is important to'treat' your surfaces before coating them to prevent issues post-paint. Before painting your floor or surface, it is important to repair any cracks, holes or expansions of joints in your concrete to prevent an un-slightly finish to your flooring once it's painted. PaintMax Pre Seal is designed to seal the surface from the out-gassing of the concrete, where air will rise and be expelled from the concrete which is often caused by a rise in temperature or a change in humidity. Another major cause to poor flooring is rising damp. Due to a poor or non-existent DPM (Damp Proof Membrane), the damp is caused by a rising water table and/or the immediate surrounding areas being waterlogged.
Air entrapment is a common issue that can occur if the surface isn't primed before being coated. This is where the air pushes bubbles into the resin coat which later bursts, leaving'craters' and'pin holes' in your floor paint. This can also be caused when the resin has been mixed too quickly - it is important to use the correct tools to mix to avoid issues. Primer tackles this issue by soaking further into the surface to fully seal the entire surface area of concrete floors. Air is then less likely to push up, and on the rare occasion that it does, the bubble will pop and the resin now being thinner, will generally revert back and refill the'pin hole' caused by the bubble.
60/80m squared per 20 litres Tub. Depending on application surface age and conditions. Dry time of coating using standard roller in areas with minimal air moisture (lab conditions). First coat should be left to dry for 24 hours to assure adhesion to surface leave minimum of 24 hours for after coats always leaving minimum of 48 hours before 100% use of area again.True 100% cure will only be 7 days after application of last coating. (Work in a well-ventilated area using no forms of naked light/fire). Please test for damp before coating by applying a small test patch or applying a clear plastic sheet (30cmx30cm) and sealing it to the floor with a high-grade tape (duct tape) without any ways of air escaping and leave for 24 hours if there are any forms of water vapour on the sheet then a potential damp issue may be present and steps will need to be taken before coatings. Mix very well before use using a drill/paddle tool. If the area you are looking to coat is virgin (never been coated) or has had contamination from oil, grease, cutting agents etc, Cleaning with correct equipment/surface preparation products will be required. Power floated/Screed areas (smooth shinny concrete) will need to be treated with an acid etch or abrade by mechanical means all product info will be displayed on the item you will take collection of.
A test patch is always advised as some areas my still have contamination and this could have complications when coating. The product Can/Tub/packaging may vary from listing picture due to stock levels and availability; Product contents will be as described in listing. PRE-SEAL ITEM IS An UNDERCOAT/SURFACE SEAL AND SHOULD ALWAYS BE OVER COATED WITH A FLOOR PAINT PRODUCT THE PRE-SEAL PRODUCT ON ITS OWN WILL NOT ACT AS A STABLE FLOOR COATING, PRE-SEAL IS COLOURED BLUE BUT WILL NOT SHOW ONCE COATED WITH TOP COAT. Floor-paint Products are polyurethane heavy duty high impact formulation and care should be taken when applied full safety data sheet can be requested. All images are for illustration purposes only including main images shade difference may happen from image to product.
Any recommendations and advice offered are given without legal responsibility. PaintMax shall not be liable to any person for any loss or damage which may arise from advice given or from the use of any of the information contained in any of the materials offered on this website. Ideal for interior or exterior use. High impact durable polyurethane paints for concrete floors, walls, wood and metal products. Collection from Epping CM16 Bromley BR1 or Halstead CO9.
Same day and Next day. Please contact before purchasing to arrange, call: 0203 589 2280.
CALL: 0203 589 2280 Full Product range avalible at. Once you have accepted the item we are no longer responsibly for the condition of the product and can not be return to us.All our coatings are manufactured in the UK to the highest quality. We have designed all our products to withstand the test of time. Specialising in heavy duty industrial flooring paints and surface coatings Barn & Timber, All weather coatings Multi surface Paints, Boat & Marine coatings Metal Work Coatings & Primers.
We welcome Trade and Bulk Orders. Please contact for discount price and more information. This item is in the category "Home, Furniture & DIY\DIY Materials\Paint, Stain & Varnish\Interior & Exterior Paint". The seller is "paintmax_shop" and is located in this country: GB.
This item can be shipped to United Kingdom.