Plasti Dip Outdoor / Indoor Spray Paint Wood Metal Stone Brick Matt Aerosol

IMPORTANT PLEASE SEE PREPARATION AND APPLICATION GUIDE SUPPLIED WITH YOUR ORDER TO ENSURE BEST RESULTS. The Original Peelable, Flexible, Insulating, Non-Slip, Durable, Rubber Coating! Plasti Dip is an air dried flexible liquid matt coating for use on virtually anything! PlastiDip can be dipped, brush coated and sprayed.

Add more layers for greater protection and grip. Seals and protects from weathering, and prevents splitting. Reduces vibration, deadens sound, and prevents corrosion. Shatter proofs glass objects (available in clear). NOTE: Surfaces which are non-absorbent such as metals should be primed using our recommended Primers, which are available in Clear and Grey.

PLEASE READ: Guide to Preparation and Application. The essential criteria is to ensure the surface is squeaky clean, grease, dirt, debris and contaminant free and thoroughly dry before coating. On vehicles or irregular shaped items, particular attention should be paid to the sills, trim, gutters, grills, any tight or hard to get to corners and gullies that you would not normally concentrate on. Wash only with hot water as some soap detergents contain residues that Plasti Dip may not adhere to.

Never use any petroleum, citric, alcohol or solvent based cleaning/care products with Plasti Dip. Do not use car care cleaning products such as wheel shines, paint wipes etc, as these often leave trace residues which could cause adhesion problems.

Remove all traces of previous wax or silicone residue from cleaning products using the correct de-greaser, particularly for metal and plastic surfaces. Clean large areas with Plasti Dip Panel Wipe degreaser. Small areas can be cleaned with Plasti Dip Dip Care Prep Degreaser. Ensure all water is removed and the area thoroughly dry before coating. AEROSOLS Refer to aerosol for instructions. Shake well before and during use. Test spray pattern on sample piece prior to application. In cold conditions, place aerosol in warm water (approximately 21°c) for 10-15 minutes before use. BLAZE COLOURS Best applied over white Plasti Dip base coat.

In common with all manufacturers advice, we recommend testing on a small inconspicuous area first to ensure suitability. Base colours can alter the final shade.

If spraying, for a professional fine finish, Plasti Dip liquid should be filtered first. For best results, temperature of the spraying area should be between 10°c and a maximum of 27°c. Liquid Plasti Dip should be thinned 50/50 by weight.

Apply the first coat as a mist coat and gradually build up the layers. The thicker the final coating, the easier it is to remove in the future should you wish. For vehicles, we suggest a minimum of 6-7 coats. For other projects a minimum of 2-4 coats is recommended depending on application method and coverage requirement. Layers are touch dry and re-coatable in 30-45 minutes at 16-22°c and totally cured/dry 24-48 hours depending on temperature.

Increase drying times in colder conditions. Plasti Dip Primer is an adhesion promoter. Only use a primer to increase adhesion if you require a permanent coating. For permanent application, keying the surface with fine grit paper will improve adhesion if required. For extra protection of your investment and ease of cleaning, we recommend using Dip Care Sealant over the final coating.

Please see our booklet supplied with your order for other handy tips and product information, including spray gun settings. Please note that pictures are for illustration purposes only.

Please note that these swatch colours are for representation only and may not be a true likeness to the delivered product. Colours can be easily mixed together to create shade variations to the colour samples shown.

Below are a selection of the Plasti Dip colours with nearest (approximate) Pantone and RAL colours shown. Pantone Black 6 RAL: 9005 C:100 M:79 Y:44 K:93 Hex: 101820. Pantone 663 RAL: 9010 C:0 M:0 Y:0 K:0 Hex: FFFFFF.

Pantone 7621 RAL: 3000 C:0 M:98 Y:91 K:30 Hex: AB2328. Pantone 7691 RAL: 5007 C:100 M:43 Y:0 K:30 Hex: 006298. Pantone 123 RAL: 1018 C:0 M:19 Y:89 K:0 Hex: FFC72C.

Pantone 173 RAL: 2010 C:0 M:67 Y:85 K:19 Hex: CF4520. Pantone 4975 RAL: 8014 C:36 M:84 Y:59 K:85 Hex: 3F2021. Pantone 7484 RAL: 6036 C:91 M:14 Y:78 K:60 Hex: 00573F. Pantone 7540 RAL: 7024 C:41 M:28 Y:22 K:70 Hex: 4B4F54. Pantone 1665 RAL: 2009 C:0 M:79 Y:100 K:0 Hex: DC4405.

Pantone 433 RAL: 5004 C:90 M:68 Y:41 K:90 Hex: 1D252D. Pantone 4975 RAL: 3007 C:50 M:100 Y:40 K:50 Hex: 3E2022. Pantone 541 RAL: 5010 C:100 M:58 Y:9 K:46 Hex: 003C71. Fluorescent Coatings emit bright light when exposed to UV radiation. A UV tube or black light is required for the ultimate effect.

Pantone 806 (closest match) RAL: 4003 C:0 M:72 Y:0 K:0 Hex: FF3EB5. Pantone 803 (closest match) RAL: 1016 C:0 M:3 Y:97 K:0 Hex: FFE900. Pantone 2945 RAL: 5005 C:100 M:53 Y:2 K:16 Hex: 004c97. Pantone 7481 RAL: 6038 C:82 M:0 Y:86 K:0 Hex: 00B74F. Pantone 269 RAL: 5022 C:82 M:98 Y:0 K:12 Hex: 582C83.

Pantone Warm Red (closest match) RAL: 3024 C:0 M:83 Y:80 K:0 Hex: F9423A. Pantone Orange 21 (closest match) RAL: 2004 C:0 M:65 Y:100 K:0 Hex: FE5000. Pantone Black C (closest match) RAL: 9017 C:74 M:73 Y:75 K:100 Hex: 222223. Pantone 7620 RAL: 3016 C:0 M:95 Y:94 K:28 Hex: B7312C. Pantone 329 RAL: 6026 C:100 M:14 Y:60 K:49 Hex: 00685e.

Pantone 173 RAL: 5002 C:0 M:82 Y:94 K:2 Hex: CF4520. Pantone 7408 RAL: 1021 C:0 M:29 Y:100 K:0 Hex: F6BE00. Pantone 5497 RAL: 7042 C:38 M:9 Y:23 K:32 Hex: 829995. Pantone 661 RAL: 5002 C:100 M:75 Y:0 K:6 Hex: 003594.

Available in four unique Earth-tone colours, is ideal for keeping your hunting, fishing and camping gear inconspicuous when you're in the wild. Pantone 417 RAL: 7009 C:33 M:23 Y:35 K:63 Hex: 65665C. Pantone 411 RAL: 7013 C:30 M:42 Y:34 K:75 Hex: 5E514D.

Pantone 7536 RAL: 7032 C:11 M:13 Y:30 K:32 Hex: A69F88. Specially designed to give a unique finish in Pearlizer. Metalizers add a shimmering metallic finish while letting the colour of the Plasti Dip show through.

With Bright Aluminium metalizer best if used over matt black or flex blue. If you require a specific or unique colour/shade of Plasti Dip mixed for you we can do it.

Simply send us a sample of the colour you require or let us know the RAL code. Minimum order is 5 litres.

Please be aware that we cannot repeat a batch, so make sure you order enough. Customised colours are available as a special order. Please note that all pictures in this listing are for illustration purposes only. Colours can be easily mixed together to creat shade variations to the above colour samples.

We aim to dispatch all orders within 24 hours of receipt on a tracked 48 hour courier service (mainland UK only). Please contact our sales team for information and prices for Next-day and Saturday deliveries. Orders placed after midday Fri and during the weekend will be despatched the following Monday.

You must take reasonable care not to damage the product whilst it is in your possession, the item/s and packaging must NOT have been opened. Plasti Dip - Protective Coating. Plasti Dip protective coating has a matte finish. If you are experiencing a cloudy or hazy finish, its likely to be caused by high humidity. Avoid these conditions or add approximately 5-10% of our Plastidip Thinners to reduce the problem.

Why is the Plasti Dip sagging or dripping? Removing an item too quickly when being dipped, is usually what causes this problem. Remove at a rate of 1 inch every 5 seconds. If experiencing runs or sags when spraying, move can further away from the surface and apply a lighter coat.

Sagging and dripping can also be caused by high humidity, high temperatures, windy conditions, and/or direct sun light. Ideal conditions are low humidity, and little to no air movement in a well ventilated area.

In some cases you do not need to prime the surface, but this is dependent on the type of material you are coating. Generally, for smooth non porous surfaces such as metal and uvpc we would always recommend using our Primer. Why isn't my Blaze colour very bright? To get the best colour result from the Blaze range of Plasti Dip, use it over a white base layer.

Is Plasti Dip safe to use on children's toys, animal containment and/or on kitchen utensils? Plasti Dip does not contain any heavy metals, and when completely dry, is considered harmless. However, it is not recommended that it be used on items that may be chewed or inserted into the mouth, as it may present a choking hazard. How thickly can I apply Plasti Dip? When following the directions, you can apply as many coats of Plasti Dip protective coating as you like. For most applications 7-10 mils thickness is adequate. Only in extreme cases or for aesthetic reasons is more thickness necessary. (Note: a mil equates to 1000th of one inch). Can I add a colourant or pigment to the Plasti Dip to create a custom colour?

Mixing different colours of Plasti Dip protective coating can be done very simply to achieve other colours. We will soon have pigments available for sale in most popular colours.

For most pigments, add approximately 1oz of pigment to 1 litre of Plasti Dip. Please also see our new product "Create Your Colour". Which combines 5 pigments with a 651ml can of clear coating.

Can Plasti Dip be used to repair a damaged dishwasher rack? While Plasti Dip has been used for dishwasher rack repair in the past, it is not recommended. Our ReRACK product is much better suited for this application, and works very well. Is Plasti Dip chemical resistant?

Plasti Dip protective coating has excellent resistance to acids, alkaline, and most common household chemicals. However, it is best to test this before going ahead with your application. Plasti Dip does have limited resistance to petroleum based products. (Please see our "HCF" coating where contact with petroleum is required).

Can Plasti Dip be used to seal electrical connections? While Plasti Dip has excellent dielectric properties (insulates against shock), our Liquid Tape Electrical product is specifically formulated and conveniently packaged for this application. Can Plasti Dip be applied to PVC? Rub acetone or finger nail polish remover in an inconspicuous area and apply Plasti Dip to test for success. We recommend applying HCF to UPVC surfaces.

Can you speed up the dry time of Plasti Dip? Very low oven heat (between 100° - 150°) may be used on a conveyor. However, the part or object should first set or hang dry for 30 minutes for the fast releasing solvents to escape. Does Plasti Dip contain polyvinylchloride? Plasti Dip does not contain any polyvinylchloride or any other vinyl resins.

Is there any product on the market that can be applied over Plasti Dip to provide a glossy finish? Our Glossifer (F-799 Top Coat) will provide a glossy finish and is currently available in 750ml and 2.5 litre and 5 litre cans and soon aerosol. Super Grip - Non-skid Fabric Coating. Can I apply Super Grip directly to the floor surface?

Super Grip non-skid fabric coating is only designed for use on most fabric surfaces to stop skidding. Do not use Super Grip directly on wood, ceramic, concrete, or other types of flooring surfaces. What if I get Super Grip on a surface I didnt intend to? DAP, Goo Gone, or mineral spirits can be used to clean up Super Grip, but try it in an inconspicuous area first to ensure the cleaning solution doesnt affect the surface you are cleaning. Can Plastiseam be used with underwater applications?

While Plastiseam is designed to seal against moisture penetration in sewn seams, it is not recommended for applications requiring permanent submersion in water. Can VLP be used to repair damaged dishwasher racks? While VLP has been used in the past to recoat damaged dishwasher racks.

Our ReRACK product is specifically formulated and conveniently packaged for this application. What is the difference between the VLP and Vyna Bond products? VLP is specifically designed for tears and splits in vinyl and some leathers, while Vyna Bond is specifically formulated and conveniently packaged for patching holes in vinyl, even under water. VLP can be sprayed by using a pressure-pot with a conventional spray gun and airless spray equipment. What can I use to reduce Liquid Tape'Electrical' if it becomes too thick, or if I need a thinned down Liquid Electrical Tape coating for my application?

Dielectric strength refers to a materials ability to insulate against electrical shock. Liquid Tape'Electrical', being rubber based, provides excellent electrical insulation and is suitable for all types of applications. Further dielectric information is available upon request. Can Liquid Tape'Electrical' be removed? Yes, carefully cut and peel Liquid Tape'Electrical' from the repair area. (Be sure to follow all health and safety warnings as well as local electrical codes when working with electricity).

Vyna Bond - Leather & Vinyl Repair. Can I use Vyna Bond on leather and other fabrics? While Vyna Bond is meant for use on vinyl and comes with a vinyl swatch for patching, it also works well on other porous fabrics and materials. It's best to test the suitability of Vyna Bond for your vinyl repair applications.

Can Vyna Bond be sprayed? Vyna Bond can be sprayed by using a pressure-pot with a conventional spray gun and airless spray equipment.

My application requires temperatures outside the range listed on your Technical Data Sheet [TDS]. Can the product go higher or lower in temperature than the range states? Generally yes, however it depends on the length of time and also how the coating is expected to perform at that temperature. If the coating will not be impacted, expected to resist abrasion, chemicals or not stick to itself or another surfaces at lower or higher temperatures, and if the period of time is relatively short, most of our coatings will go outside the range before either becoming affected negatively. Its always best to test if this is a critical feature, and use a'common sense' approach.

The MSDS says the product is flammable or hazardous. Does this mean its flammable or hazardous in its liquid state or after its applied and allowed to adequately dry? Many customers confuse MSDS information [based on liquid properties only] for physical properties of the applied and properly cured product. MSDS information is for transportation, safety, health and environmental reporting purposes only of the liquid product.

Always review the TDS for the product's physical properties after completely drying. How do I calculate the amount of coating I need for my project?

First determine how many mils thick you require the product to be applied when dry. Then calculate the square foot of the surface area of each part to be coated. Using the square foot coverage information provided on the TDS, you can easily calculate how many square feet per gallon you can expect at a given mil thickness.

The 20 square feet per litre would then become twice the thickness or 10 mils dft. You can multiply or divide accordingly to achieve your estimated per litre coverage. (mils: 1 mil = 1000th of 1 inch). By dividing into your cost per litre for the product you can then theoretically estimate the amount of material needed for the job, as well as a rough cost per square foot. Always assume you will have some waste whether you are dipping [usually 5% waste], brushing [usually 10% waste] or spraying [usually 10-25%] depending on shape and complexity of parts being coated.

These are estimates only and common sense must be used when calculating material usage. The product TDS states I must sheer mix the product. What does sheer mixing mean, and how does that differ from using a stir stick or paddle mixer? Sheering or aggressive dispersion is necessary for products that gel or coagulate in cold weather, transportation or long term storage. Most of our vinyl based Muraculon products require this type of mixing. High speed combined with a Cowles dispersion blade or similar is required along with carefully following the TDS mixing instructions. Over 95% of all application/finish complaints stem from improper or inadequate product mixing. Please read and follow instructions very carefully! In many cases we have several colours available in the product you need. If you can supply us with a 2 inch x 2 inch colour swatch, we can check to see if we can match the colour youre looking for or something very close. In most cases we can offer a Bespoke colour service for a small addition charge. We require a 5 litre minimum order for Bespoke colour requests.

You can access many of our MSDS and TDS through our website. Provide us with as much detail as possible; we cant have too much information about your application. We may also ask you to send us a sample or actual part you are interested in coating so we can evaluate your application specifics and provide you with the best overall coating.

In some cases our Technical Team will offer to come and visit you to discuss your technical requirements. MILS: One mil is equivalent to 1000th of one inch. The item "Plasti Dip Outdoor / Indoor Spray Paint Wood Metal Stone Brick Matt Aerosol" is in sale since Wednesday, August 1, 2018. This item is in the category "Home, Furniture & DIY\DIY Materials\Bricks, Stones & Concrete Blocks". The seller is "plastidipukltd" and is located in Petersfield.

This item can be shipped to United Kingdom.

Custom Bundle: No
MPN: PDL-SPRAY-WRAP
Non-Domestic Product: No
Modified Item: No
Brand: Plasti Dip