Easy to apply, with low maintenance. Resistance against cracking, blistering, flaking.Contains a biocide to protect against fungal degradation. Rain and severe weather resistance. If you can't find the colour you want just select'My Colour Isn't Listed' and let us know at checkout! Zinsser AllCoat Exterior Matt is self-priming and will bond to existing glossy paints without sanding. After removing existing mould and mildew, two coats of AllCoat Exterior Matt will ensure that any exterior looks bright and beautiful for years. Not the product you need? Please refer to the product Data Sheet for more uses. Further Details and Technical Data. Surfaces should be clean, dry, sound and free of any contamination that may interfere with adhesion. Remove all loose or peeling paint and chalky paint residue. Sand edges of any remaining paint film until smooth.
Special precautions should be taken during surface preparation of pre-1960 paint surfaces as they may contain harmful lead. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding.
New concrete, masonry and other related surfaces must be cured at least 30 days before priming. Remove all existing mould and mildew before painting. Timber at risk from decay or insect attack should be treated with an appropriate preservative. Zinsser AllCoat Exterior Matt is self-priming and will adhere to any sound surface. It bonds to existing glossy paints without sanding.
The first coat of AllCoat Exterior Matt primes and seals the surface, providing a base for the topcoat. The topcoat completes the sealing process while providing additional moisture resistance and protection. Before painting, fill all nail holes and gouges.
Where necessary, spot prime knots and sap streaks with Zinsser B-I-N® Primer-Sealer. For new or unpainted cedar, redwood, or other resinous timbers prime with Zinsser Cover Stain®. Shake or stir well before using. Apply with synthetic bristle brush, roller or sprayer.For airless spraying, use a. Ensure air and surface temperature are between 10° and 32°C and humidity is less than 85% during application and cure of the product. Avoid painting in direct sunlight and maintain a "wet edge" to avoid lapping. Ensure conditions during application and cure are favourable, do not apply if there is a likelihood of rain, frost, fog or condensation affecting the freshly applied paint before it has fully cured. Zinsser AllCoat Exterior Matt is available in a full range of BS4800, RAL and NCS colours. Multiple containers of tinted paint should be intermixed (boxed) to ensure colour uniformity. Per litre on non-porous surfaces. On porous surfaces coverage will be reduced, e. Per litre; planed timber 8-12m. Normal application is 2 coats; however, an additional coat should be applied to areas of high exposure, such as sills and fascia boards. Clean application tools, spatters and spills immediately with warm water and liquid detergent, before rinsing with clean water.
Dried paint on brushes can be removed with Zinsser BIN Brush Cleaner. Remove dried product with a household cleaner, such as Zinsser Universal Cleaner and Degreaser, before rinsing with clean water.
Zinsser AllCoat Exterior Matt (Water-Based) is not intended for application to exterior floors, decks or any surface subject to water immersion or prolonged contact with water. Touch dry: 1 hour at 21°C.Hard dry: 4 hours at 20°C and 60% RH. Recoat: 1 hour at 20°C and 60% RH. Drying and recoat times will be extended at lower temperature and higher RH. Typical film thickness per coat: 40 microns.
Matt Finish Density: 1.25 kg/litre. Shelf life: 2 years in unopened containers.
Storage: store indoors at 5 - 25°C. This item is in the category "Home, Furniture & DIY\DIY Materials\Paint, Stain & Varnish\Interior & Exterior Paint". The seller is "industrialcoatingsltd" and is located in this country: GB. This item can be shipped to United Kingdom.